考题代号：000-109
考题名称：Virtualization Technical Support for AIX and Linux - v2
版本号：V9.02
考题数量：66 道题
1.An administrator has the following configuration on a VIO Server:
Why is this error being displayed?
A. ent3 is configured as 'standard' instead of '802.3ad'
B. ent3 is a LHEA port and requires the -L flag
C. ent3 has no interface connected
D. ent3 is controlled by the SEA
Answer: D
2.An administrator needs to update a legacy VIO server (VIOS) partition from version 1.5 to the most
current version. The rootvg of the VIOS server is presented from SAN and is managed using the
SDDPCM package.
Which of the following must be considered?
A.The latest version of SDDPCM should be included in the NIM lppsource for the upgrade.
B.The IBM supplied scripts and procedures should be followed in order to migrate VIOS with SDDPCM.
C.SDDPCM is now included in AIX 6. Upgrading of the package will occur automatically.
D.SDDPCM must be upgraded immediately before the VIOS migration.
Answer:B
3.After applying the latest Fix Pack to a VIO server, the administrator finds an issue with the hosted media
repository. The lsrep command fails with the following error :
"Unable to retrieve repository date due to incomplete repository structure"
What is the most likely cause for this error?
A.The VIO server has not been rebooted since applying the Fix Pack.
B.The Fix Pack reset the date and time to the shipped default.
C.The repository was in a loaded state prior to applying the Fix Pack.
D.The reboot caused the repository to forcibly unmount.
Answer:C
4.After installing a new VIO server partition an administrator noticed that the time zone is incorrectly set to
CST6DST. The administrator would like the time zone set to Europe/London. Which command will
achieve this?
A.chdate -timezone Europe/London
B.chzone -zone Europe/London
C.chtime -tz Europe/London
D.chsys -timezone Europe/London
Answer:A
5.A dedicated LPAR has two dedicated Fibre Channel HBAs assigned to it.
In order to reduce the amount of hardware, the LPAR will be migrated to a currently running VIO server.
The administrator collects some server performance from the VIO server and notices that the I/O peaks at
5.5Gbits and runs at an average of 4Gbits per second.
The VIO Server runs two dual port 8Gbit FCS cards, so the load is not affected by other LPARS on the
VIO Server.
Which of the following is the most cost-efficient configuration for the VIO client?
A.Assign vSCSI disk for the new client LPAR through prioritized channels.
B.Assign one of the ports in the 8Gbit Fibre Channel HBA, using NPIV directly to the new client partition.
C.Dedicate two new Fibre Channel HBAs to the VIO Server and use them to exclusively host the vSCSI
disks for the new client partition.
D.Install SDDPCM drivers onto the VIO Server, set up the client LPAR and run the following command:
"datapath priorities vhostX fscsi0 fscsi1 fscsi2 fscsi3".
Answer a
6.When installing a Linux LPAR from an AIX NIM server, what steps are required?
A.Add LPAR details to /etc/bootptab
Copy DVD to a local directory and add directory to /etc/exports
Copy network boot kernel to /etc/tftpboot
Boot into SMS and configure remote IPL settings
B.Configure LPAR as a NIM client
Copy DVD to local directory
Configure Linux SPOT
Boot into SMS and configure remote IPL settings
C.Add LPAR details to /etc/tftp/other/kernel.conf
Copy DVD to local directory and add to /etc/exports
Copy network boot kernel to /tftpboot/kernels
Boot into SMS and configure remote IPL settings
D.Copy DVD to local directory and export via /etc/exports
Copy network boot kernel to /etc/tftpboot
Define LPAR as a NIM client and initiate a bosinstall
Boot into SMS and configure remote IPL settings
Answer:C
